QUADIFYRC.COM
  • RC Cars
  • Car of the Month
  • Quad Reviews
  • COUPONS AND DISCOUNTS
  • About & Contact

QUADIFYRC Quadcopter reviews

Beebee 66 By Fullspeed RC - not quite there yet

9/1/2018

0 Comments

 
Picture
The Beebee 66 is a micro 1s brushless powered quadcopter which is essentially a brushless Tiny Whoop. It is made by Full Speed RC, the same company that produced the highly successful Leader 120. (review here). Gearbest kindly supplied me a BNF Beebee 66 to review. I was desperately hoping for this to be the brushless answer to the tiny whoop but I'm really bummed out that it just isn't. Read on to find out why.


Adding a receiver
Since this was supplied as a BNF model, it came without a receiver. I opted to use the lightest FRSKY receiver I had on hand - an XM that I'd finally figured out how to fash with the RSSI channel 16 firmware. In most models this is a matter of soldering wires to the exposed pads on the top of the flight controller. However,since the FC and ESC are part of the structure of this quad AND the FC is flipped upside down to sit the ESC connector in a manageable location, the prop gaurd, 4 nylon nuts and the flight controller itself had to be removed before I could access the receiver solder pads. Then I needed the help of a multimeter to figure out ground, +5v and signal wires. Once soldered up with a short length of silicon wire to the receiver it was easy enough to re-assemble and tuck the XM reciever underneath the canopy behind the AIO camera/VTX. Pics below of course can explain this better:

Picture
Canopy and prop gaurds removed to allow access to flight controller
Picture
No instruction manual provided so please feel free to take note of pads for connecting to ibus or sbus receiver

It's not the end of the world wiring in a reciever here but can be fiddly with particularly small hardware. I'd recommend if you did buy this model that you purchase with the receiver of your choice pre-fitted.

Betaflight Setup
Kept it pretty simple here. Because this is quite a different steup than I am used to I retained the stock settings on Betaflight 3.1.7 that it arrived with. All I did was set an arm switch and a mode switch for angle-horizon-air. Below are the default settings from Betaflight 3.1.7. Oh yeah, receiver had to be set up too. Like most f3 boards receiver is on UART 3.
Quad Prep
The only other preparation was pretty straighforward. The included GNB High Voltage 1s 260mah Lipo battery was easily charged using the included USB adaptor and a micro usb cable I had on hand. Only 1 set of props was included that are press-fitted on the tiny 0705 fullspeed branded (Sunny Sky made) 0705 brushless motors. I left the VTX on the default channel for the initial flight that my Aomway Commanders (review here) picked up as 5905MHz.

First flight
Please look away if you love your Beebee 66 because it starts to get a bit ugly here. After fully charging the LiHV batteryand confirming everything was working ok I armed and found the props were fouling on the TPU canopy. Minor annoyance down to the tight tolerance in the slightly flexible TPU canopy. Easy enough to bend out of the way and I was back in action.

The first thing I noticed how loud the motors are - not in idle where they are practically silent but under any sort of load. Next as part of test with  line of sight attempting a 'punchout' I could clearly see the quad dipping (pitch/roll) and twisting (yaw) under load. I'll attempt to tune this out later on and will post another review if successful. Moving on to line of sight I found the flight performance dull and uninspiring. What's worse was that after just one and a half minutes flight my battery was sagging down below 2.7v - the motors were clearly very demanding for their relatively mild output. I really wanted this quad to be a success and in fairness there is a chance I could have a less than perfect unit but my experience is my experience and I was disappointed. I do have some thoughts on how to improve though and I'll cover this in my Next Steps section below.

Comparison to a brushed micro
Please understand that these comments aren't made from isolation - I've had some experience with tiny whoops based on 7mm motors (like the JJRC H67 or Eachine E011) and although these are cheap brushed toy grade quads, they offered equivalent or better power and a flight time of 4 minutes plus on the same size battery with much smoother flight performance. A quick note that I actually tried the stock battery from the JJRC H67 (260mah non-HV) and got only 1 minute flight before it sagged below 2.7v under load. After recovery it bounced back to 3.65V but this same battery give my 4 minutes plus in my E011 FPV or santa whoop​.

Recommendations
At this point I can't recommend this quad. The performance I experienced was poor and the flight time was unacceptable. My guess it that the brushless motors do not scale down well to 7mm, at this size the brushed motors seem to be more approprate. I'd recommend going in one of two directions:
1. Tiny whoop based around 0716 (7mm) brushed motors. Something like the Santa Whoop I made here. It is much more simple, much less expensive, quieter and more durable against crashes. Motors will need replacing after 30-50 packs but are inexpensive.
Picture
2. Brushless micro based on 1103 motors and 2s. The 0705 motors on the beebee 66 have shown me that right now this is a step too far for brushless. On the other hand even the budget racerstar 1103 motors perform well (no longer available get the eaglepower 1103s instead) on a 2 inch lightweight quad with a small 2s battery. See my build here for a lightweight 2s quad that I really miss right now (had to salvage parts). Good news is I have more parts on the way for an even better build!
Picture
Next Steps
I'm not content to leave things be with the Beebee 66 and the latest version of this model (Beebee 66 lite) has shown the direction I want to go in - removing weight. I'm skeptical of getting to the level of improvement I want but with some of the parts below I think I can replace the canopy with a simple camera holder. remove the propgaurd and TPU supports and save up to about 4g. Will this make enough difference? Not sure but will report back when I'm done. Make sure you bug me about the follow up in the comments if I'm too slow! Below are some of the weights of the components I'm interested in:
0 Comments

    Quick Access Menu

    All
    1103
    1104
    1105
    1106
    1204
    120rs
    1505
    20mm
    2207.5
    2508
    2.5 Inch
    2 Inch
    2s Whoop
    3 Inch
    4s Micro
    5 Inch
    6s
    7500kv
    7 Inch
    Action Cam
    Adapter
    AIO
    AirA
    Antenna
    Aomway Commander
    Ascent
    Asteroid
    Babyhawk R
    Battery
    Beebee 66
    Beeper
    Bench Review
    BNF
    Boldclash
    Bolt
    Brushless Whoop
    Budget
    Build
    Canopy
    Charging
    Christmas
    Cinewhoop
    Cloud 149
    CM275T
    Cobra
    Comet
    Crossfire
    Crux3
    Diatone
    Drone
    Dvr
    DYS
    Eachine
    Eachine Cvatar Cinewhoop
    Eachine Shadow Fiend
    Eachine Tyro79
    Eachine Vrd3
    Emax
    ESC
    F02h
    F3
    Fatshark
    Fatshark Attitude V5
    First Flight
    FlexRC
    Flight Controller
    Flyfox 110
    Fpv
    Frame
    Freestyle
    FRSKY
    FRSKY X-lite
    Ft5
    Full Speed
    FUS Spartan
    FUS X111 Pro
    Gemfan 2540
    Goggles
    Goggle Strap
    Happymodel
    Hawk 5
    Hawkeye Firefly 2
    HB64
    HD Footage
    HGLRC
    Hobbycool
    HobbyCool.com
    Iflight
    Isdt
    JHEMCU
    Jr Port
    Jumper T8SG
    Komori
    Lal5
    Larva-x
    Leader 120
    Leader 2.5
    Leader 3
    LED
    Long Range
    LST S2
    Micro Quad
    Mobula
    Mobula7
    Motors
    Namelessrc
    Novice-i
    Oled
    ORT Dual Shield
    PIDs
    Pnp
    Portable
    Propellers
    R249+
    Racerstar
    Radiomaster TX16s
    Ready To Fly
    Red Devil
    Review
    Roma F4
    Roma F5
    Runcam
    Runcam 5
    Rush
    Sailfly X
    Sailfly-x
    Shootout
    SKY03O
    Skystars
    Skyzone
    Smart Audio
    Snapper7
    Sweet Spot
    Taranis
    TBS Tango2
    Tinyleader
    Tiny Tank
    Tmotor
    T-motor
    Toothpick
    Toothpick Pro
    TP3
    Transmitter
    Trashcan
    Tutorial
    Twig
    TX01
    Upgrade
    V1s
    Vtx
    Whoop
    X120
    X Lite
    X-lite
    ZJWRC 115X

Thanks for visiting QuadifyRC.com Follow us on facebook below to get all the latest updates
  • RC Cars
  • Car of the Month
  • Quad Reviews
  • COUPONS AND DISCOUNTS
  • About & Contact