FLEX RC Komori 3 inch lightweight build

Ever since I saw the first image of the first FlexRC Ascent I've been impressed. It is a simple micro quad frame that accepts 2" propellers, is super lightweight and has a cage that is designed around a micro CCD camera (runcam micro, foxeer micro, caddx micro, furibee micro etc.) This was one of the first frames designed around these superior cameras and in my opinion still one of the best.

Flex RC Ascent 2" frame is under 10g

The flexRC Komori 3" weighs just 14.5g

Dmitry from FlexRC has since expanded on this winning formula and this has given birth to the 2.5" Ascent, 3" ascent desinged around the runcam split and most recently the Komori 3". The Komori is essentially based on the original 2" with a baseplate embiggened to take 3 inch props and extra torsion supports between front and rear arms to allow for minimal flex whilst stick with thin (but lightweight) baseplate. All up weight of the frame is 15g with included hardware. Shape is a squashed x - front and rear motors are closer together than left/right motors. *Theoretically* this should mean more stability but slower movement on roll and faster but less stable in pitch.

After spending a lot of time with the Leader 120, I was looking forward to a frame that better fits the micro CCD camera and can take a genuine 3" prop rather than 2.8".

Build
For build components I essentially transferred my gear across from the Furibee X140 (review here) where I felt the heavy frame (although durable) was letting the performance down. 

After initial flights I decided the 1306 weren't suitable - performance was dull on 3s albeit and improvement on the Furibee X140 owing to roughly 30g less weight in the frame. This is when I switched motors to the HGLRC Flame 1105 6000kV (reviewed here).

The build on this was really simple - FC/ESC/VTX were all bolted on to the baseplate as were the motors. I just love the way the side plates clip on with no fuss and still had plenty of room for the 3-layered stacks. Once in place itwas easy to add the 2 nylon standoff supplied which can be used place cable ties on as additional support for receiver and VTX antennas.

Components used:

Flex RC Komori 3" frame

HGLRC FLame 1105 6000kV motors

Furibee Micro CCD camera

Gemfan 3025 propellers

Furibee X140 flytower (VTX, FC, ESCs and 1306 motors)

Turnigy Nanotech 3s 450mah 65C battery

 @s Betaflight setup
Since this is a custom setup I won't go into betaflight setting but to summarise I went with

• Reverse prop direction (clean lens)
• Dynamic filters on, notch filters off, PT1 quad type
• Stock pids betaflight 3.2.2

Flight
I went into more detail on the performance of the motors here but overall 3s paired with these motors and overal setup was excellent. My Leader 120 on 3s was always very quick but was a tad unstable and highly strung. The Komori I felt fixed this feeling of instability - flight was a lot more predictable with linnear power and no twitching. What this translated to in reality was more enjoyable less stressful flight with no loss in top speed compared to the leader. 2s on this quad is ok - not as fast as the leader on 2s but I think some more agressive props like the Gemfan 3035 triblades would be better, This is primarily a 3s quad - I have no interest in 4s.

Durability
I've not yet put a lof of packs through but have already had a reasonable sideways landing on to rough chip tarseal. From this the carbon fibre that extends beyond the motors for production has had a slight delamination but nothing that affext performance. There is however a lot of material that extends beyond the motor meaning I could file back to removethe delaminated portion. It also means the motor was well protected in the crash - not a scratch on it.

Conclusion
It's no secret that I am a fan of light builds - going lighter means better agility and longer battery life as well as better resistance to crash due to less mass. The FlexRC Komori frame fits my desire for a 3 inch frame perfectly - super light with frame designed natively around a micro CCD camera. The komori does sacrifice a bit of durability for it's light weight but given I fly over grass mostly I'm happy to compromise a bit of durability for weight. Since the frame is light this then allowed me to choose lighter duty motors and batteries - which makes the entire build light. As well as the benefits above, lighter motors and batteries tend to be cheaper too.

Flight characteristics were excellent andI felt the combination of 3s 450mah - 1105 6000kV - Gemfan 3025 offered a well balanced combination of power, agility, stability and efficieny (i.e. longer flight times. I think my favourite Leader 120 has finally been bettered.