leader 120 pnp micro fpv quad From Gearbest - Part 1: bench review

Firstly, thank you to Gearbest for supplying this model in exchange for a full review including my observations and recommendations from having built a very similar quad from parts. I'll review here and then run a series of tip, tricks, mods depending on how it flies stock. You can find the PNP version (no receiver) here. As at September 2017 try code HarvestRCnew7
to get this for only $US93.99!
​
I'm going to skip the unboxing, I don't have anything to add other than the picture of all the parts included below, so straight to the good stuff.

---

---

The parts included and build quality have improved...

First off the motors are no longer and unbranded red 1104 7500kv. They are now branded SZ speed and full speed but are still rated the same. From what I can see the shaft length extending through the bell is shorter. Great idea - the only job this does is to centre the prop which the screws hold on. Less stress when trying to put tight props on (looking at you Gemfan 2035) and you don't have a 1.5mm drill bit. Below is a comparison to my DYS 1104 7500kV. You can see my review on these here

The comparisons to these motors don't stop there. Both are similar external size, and the magnets are simlarly strong - very notchy compared to the racerstar motors. From there the leader 120 motors are better. Wires are multicore, slightly thicker and much more flexible and easy to manager. On spin up in betaflight they are so quiet and smooth! Not noisy like the DYS even when they were new. In fairness the DYS are powferful so if the stock leader 120 motors get anywhere near this I'll be happy, especially given the improvements.

This flight controller and ESC is ubiquitous and first appeared on the ARFUN90. I've reviewed one in full here - in short reliable and well featured. What impressed me here was the quality of soldering and the cable managent, just so clean - see below. I wasn't going to compare my efforts but I'd already soldered in the receiver and the macro image makes me feel inadequate! From what I can see of the earlier reviews, this looks to have improved substantially.

Betaflight setup and the Flip of Death

This model shipped with the full release at the time of writing - 3.1.7 (3.2.0 still in release candidate). Interestingly along with the physical changes the software settings have been changed to address some of the brownout/flip of death issues the early reviews had. Most notable digital idle is set at 10%. Since I'll maiden this with stock settings I'll go with that and see if moving back to my standard of 3.5% is still viable. 10% is not ideal for me as you will never be able to fully chop throttle for flips and whatnot. Cool to see that they have addressed it and looking forward to seeing if this issue may have gone altogether.

I'll post some pics of the key betaflight screens for prosperity below (flip through them) but I intend to move to 3.2.0 as soon as I have completed initial flights and can confirm everything is functioning as expected.

Weight

I'm something of a lightweight jukie when it comes to miniquads, benefits include longer flights, better agility, greater crash resistance through lower intertia. See the gallery below for the various weight measures but in short 64g dry, 94g AUW ready to fly with the stock 2s 500mah battery. This include an ibus FS82 1g receiver which was not present when I too the photos.

This is a very respectable weight for a micro that swings 2.8" props as these props generate a significant amount of lift in combination with a motor of this rating.

All this and it includes my favourite beeper/led combo (reviewed here) - a beeper is a must for micro quads as you can loose them even in short grass! I can anyway.

Size comparison to other micros

This is not a big model by any stretch. The beauty of these micros - and to be clear this is still a micro - is you can fly in small areas (not indoors!) with less danger and concern to the public. They are also quick to get in the air and consumables like batteries and props are cheaper too. This model measures 120mm diagonally motor to motor and offers most of the experience of a 5" FPV quad. Picture below compare to an E011 typical tiny whoop and an 80mm EYAS x2 with 2" props