QUADIFYRC MODS AND REVIEWS
  • RC Cars
  • Car of the Month
  • Quad Reviews
  • Quad Mods
  • COUPONS AND DISCOUNTS
  • Long Range
  • About & Contact

TIPS and TRICKS

Best version of betaflight for the Leader120 and other f3-based micros

21/8/2018

3 Comments

 
Picture
A quick announcement - user sbstnp from the RCGroups Betaflight Thread has kindly recompiled the betaflight Omnibus F3 target to allow the good stuff - RC smooting, absolute control, Iterm relax and even LED Strip. For those of you familar with the 3.4.0 'performance' version this is much the same but for 3.5

If you are not familiar this file will allow you to run all of the great new features of betaflight 3.5.0 that make it more suitable for micros (esp new dynamic filter and feedforward) and the massive improvements from 3.4.0 as above. I strongly recommend this for your leader 120 or any other micro brushless as all tend to run the OMNIBUS (F3) target. Will follow up with install guide in a few days. Full credit goes to sbstnp for this recompile.

Hex file can be found here:

betaflight_3.5.0_omnibus.hex.zip
File Size: 282 kb
File Type: zip
Download File

For my list of recommended hardware changes please see my blog: My leader120 is a year old! What I've changed in that time
3 Comments
Nick
22/8/2018 11:42:17 am

Hi there, I downloaded the betaflight 3.5 to my leader 120 and am trying to figure out the tune. I am running a gnb 550 3s and I am getting oscillations. Running the gemfan 2540's . Anything that should be tweaked in the stock settings.

Reply
QuadifyRC
23/8/2018 11:14:26 am

Hi Nick

Before you start changing the tune make sure all your props are new, check motors for noise and trueness of shaft and make sure evrything that is meant to be tight is tight. Once that is all checked off check the betaflight 3.4 and 3.5 tuning guides and then look at your tune. Try drop pitch and roll p and d values by 50% and gradually work your way back up untill you hear oscillation on that axis and back off a little again, This is a little oversimplified but a start. I'll share my diff once I've had a play.

Reply
ArcherFPV
19/1/2019 02:54:15 am

Very cool! I’m definitely going to have to try this with my babyhawk r with 2.5” arms as soon as I get new motors.

Reply



Leave a Reply.

    Archives

    November 2020
    July 2020
    January 2020
    December 2019
    October 2019
    September 2019
    August 2019
    July 2019
    June 2019
    May 2019
    April 2019
    March 2019
    February 2019
    January 2019
    December 2018
    November 2018
    September 2018
    August 2018
    July 2018
    June 2018
    May 2018
    February 2018
    December 2017
    November 2017
    October 2017
    September 2017

    Categories

    All
    1.9 Inch
    2 Inch
    2s Whoop
    3.4.0
    3.5
    3d Printing
    5.8GHz
    6 Inch
    6s
    AKK
    AKK Infinite
    Antenna
    Attitude V5
    Battery Pad
    Beeper
    Betaflight
    Brushless Whoop
    Cheap Mods
    Dji Fpv
    Dshot
    DVR
    Eachine
    Eachine Trashcan
    Emax
    Fatshark
    Fullspeed
    Furibee X140
    Goggles
    Happymodel
    Hawk 5
    Hawk 6
    Headstrap
    Hq Props
    Iflight
    Jello
    King Kong Fly Egg
    Larva X
    Larva-x
    Leader 120
    Lightweight
    Micro Brushless
    Micro CCD
    Micro Quad
    Mobula
    Mobula6
    Mobula7
    Mobula7 Upgrade
    Omnibus
    OSD
    Pids
    Propellers
    Red Devil
    Repair
    Runcam Nano 2
    Sailfly X Upgrade
    Sailfly-x Upgrade
    T65mm
    Throttle
    Throttle Limit
    Thrust
    Tinyhawk
    Tinyleader
    Trashcan
    Upgrade
    USB Charger
    VTX
    Walkthrough
    X2 Elf
    Xlite

    RSS Feed

    follow us in feedly
Thanks for visiting QuadifyRC.com Follow us on facebook below to get all the latest updates
  • RC Cars
  • Car of the Month
  • Quad Reviews
  • Quad Mods
  • COUPONS AND DISCOUNTS
  • Long Range
  • About & Contact