QUADIFYRC.COM
  • RC Cars
  • Car of the Month
  • Quad Reviews
  • COUPONS AND DISCOUNTS
  • About & Contact

TIPS and TRICKS

THROTTLE LIMIT IN BETAFLIGHT 3.4 and Up: Longer battery life and cooler motors

10/7/2018

12 Comments

 
PictureThrottle limiting is useful in this 1103 powered quad which uses very cheap motors. Click to see ultralight 2" brusless build
 Introduction
Update: This is relevant for all versions of betaflight 3.4.0 and up.

One of the new "minor features" in betaflight that I'm very excited about is throttle limit. Previously throttle limit could only be done through your transmitter software and is a pig to set up and even if you could set up it is difficult to flick between option.

For the first time this can be set up in Betaflight with the release of 3.4.0. I'll cover only one type of throttle limit here that will most commonly be used and how to assign varying limits and rates to a transmitter switch. I've put this tutorial together because the throttle limit feature must be accessed through the command line interface (CLI) rather than the graphical user interface (GUI)

Firstly if you have played with rate profiles in betaflight before, this is what your the throttle limits are tied to. You can cycle through these with the betaflight OSD when disarmed or if you assign to switches you can change mid flight.

Why would I want to limit throttle?:
There are a few reasons that are all based around the fact that lmiting throttle will limit current drawn and so limit max RPM and thrust.
  • Longer flight. Assuming you hit 100% throttle on you transmitter at time you'll use less power and so get longer flight. This is often a trick used by racers on particular tracks where battery life is critical
  • Less vibration. Depening on the age of motors and props, limiting max throttle will limit motor output. If you motors or props are slightly unbalanced, this will limit their impact. I find this useful on my micro brushless quads with questionable motors
  • Less peak thrust. This is a good one for beginners. On 5" quads where 4s is generally the norm, beginners can limit thrust to make it behave like a 3s in terms of performance. That way you don't have to buy 3s batteries which are rapidly becoming obsolete in this size.
  • More gentle on batteries and electronics. It is large current loads that tend to be damaging to electrical systems. For batteries in particular limiting throttle will limit current draw and may mean longer service life of your battery.

Picture
Limiting throttle on a race quad can help extend battery life during races on powerful setups. Click picture to see Emax Hawk 5 review
Picture
Even on lighter builds throttle limiting can widen your choice of props. Click picture to see this 4" tooth fairy build
It's important to note that your flight controller still has full access to 100% of your throttle meaning that there will be overhead to speed up motors to perform maneouvres and corrections rather than slowing down saturated motors.

How do I do it?
Easy.
First, choose the rate profile you'd like to limit throttle on, up to 6 are available in betaflight now but I only use 3 since I map to a 3 way switch on my transmitter. In the example below I have my 'race rates' on profile 1 and 2 which are identical and use profile 2 for limiting throttle. FYI profile 3 is my freestyle rates. Make sure you press 'save'.
Picture
Next go into the CLI mode. type or copy and paste as below:

set throttle_limit_type = scale
set throttle_limit_percent = 85
save

In this example the throttle _limit_type is scale where it creates a linnear throttle curve up to the throttle_limit_percent value. In this case the throttle will linnearly increase to 85% at max throttle on your transmitter. 

If you wish to turn throttle limiting off again, use:

set throttle_limit_type = off
save

Lastly there is a second throttle limit type "clip" which simply makes the throttle stick have no impact over a set percentage. I think it will only be exceptional case where someone might use this, particularly playing practical jokes on your mates when you have access to their quad. 

To confirm that your throttle limit settings have stuck you can see in you CLI "diff" as below:
Picture
As per the example I used, my rate profile 2 (shown here as rate profile 1 since betaflight uses n-1 naming) has throttle limiting as scale limited to 85% maximum.
Setting it to a switch
The real usefulness comes in when you set to a switch so I've taken a screen grab to best illustrate - click to embidden. In this same example
  • rate profile 1 = race rates with access to 100% throttle.
  • rate profile 2 = race rates with access to 85% throttle.
  • rate profile 3 = freestyle rates with access to 100% throttle.

Flick the 3 way aux switch will have rate profile 1 in the 'up' positiion, 2 in the 'mid' position and 3 in the 'low' position. I use this across ALL of my brushless quads: 2", 2.5", 3", 4", 5", 6". Now that betaflight has 6 profiles you can get creative and map to a potentiometer or whatever else smokes your tyres.
Picture
Conclusion
In practice this works well for me on quads with older motors that either vibrate or prop/motor combinations that don't practically put out any more thrust after a certain amount of throttle, rather they just draw more current. I do really like the new filtering of the newly released 3.4.0 but for me throttle limiting is one of the most underated features in this release which I expect to see in all subsequent releases too.
Reference:
The original betaflight throttle limit pull request can be found here:
https://github.com/betaflight/betaflight/pull/5608
More tips and tricks articles can be found here
12 Comments

    Archives

    November 2020
    July 2020
    January 2020
    December 2019
    October 2019
    September 2019
    August 2019
    July 2019
    June 2019
    May 2019
    April 2019
    March 2019
    February 2019
    January 2019
    December 2018
    November 2018
    September 2018
    August 2018
    July 2018
    June 2018
    May 2018
    February 2018
    December 2017
    November 2017
    October 2017
    September 2017

    Categories

    All
    1.9 Inch
    2 Inch
    2s Whoop
    3.4.0
    3.5
    3d Printing
    5.8GHz
    6 Inch
    6s
    AKK
    AKK Infinite
    Antenna
    Attitude V5
    Battery Pad
    Beeper
    Betaflight
    Brushless Whoop
    Cheap Mods
    Dji Fpv
    Dshot
    DVR
    Eachine
    Eachine Trashcan
    Emax
    Fatshark
    Fullspeed
    Furibee X140
    Goggles
    Happymodel
    Hawk 5
    Hawk 6
    Headstrap
    Hq Props
    Iflight
    Jello
    King Kong Fly Egg
    Larva X
    Larva-x
    Leader 120
    Lightweight
    Micro Brushless
    Micro CCD
    Micro Quad
    Mobula
    Mobula6
    Mobula7
    Mobula7 Upgrade
    Omnibus
    OSD
    Pids
    Propellers
    Red Devil
    Repair
    Runcam Nano 2
    Sailfly X Upgrade
    Sailfly-x Upgrade
    T65mm
    Throttle
    Throttle Limit
    Thrust
    Tinyhawk
    Tinyleader
    Trashcan
    Upgrade
    USB Charger
    VTX
    Walkthrough
    X2 Elf
    Xlite

    RSS Feed

    follow us in feedly
Thanks for visiting QuadifyRC.com Follow us on facebook below to get all the latest updates
  • RC Cars
  • Car of the Month
  • Quad Reviews
  • COUPONS AND DISCOUNTS
  • About & Contact