# 

# diff all

# version
# Betaflight / STM32F405 (S405) 4.2.0 Jun 14 2020 / 03:04:22 (8f2d21460) MSP API: 1.43

# config: YES

# start the command batch
batch start

# reset configuration to default settings
defaults nosave

board_name VGOODRCF4
manufacturer_id VGRC
mcu_id 003a00435553501120313156
signature 

# name: QRC T79 Cine

# resources
resource MOTOR 3 C08
resource MOTOR 4 A10

# feature
feature -LED_STRIP
feature -AIRMODE

# beacon
beacon RX_SET

# map
map TAER1234

# serial
serial 1 2048 115200 57600 0 115200

# aux
aux 0 0 0 1975 2050 0 0
aux 1 0 2 1975 2050 0 0
aux 2 13 0 1475 1550 0 0
aux 3 35 0 1950 2050 0 0

# adjrange
adjrange 0 0 1 950 1075 12 1 0 0
adjrange 1 0 1 1450 1550 12 1 0 0
adjrange 2 0 1 1950 2075 12 1 0 0

# vtxtable
vtxtable bands 5
vtxtable channels 8
vtxtable band 1 BOSCAM_A A FACTORY 5865 5845 5825 5805 5785 5765 5745 5725
vtxtable band 2 BOSCAM_B B FACTORY 5733 5752 5771 5790 5809 5828 5847 5866
vtxtable band 3 BOSCAM_E E FACTORY 5705 5685 5665 5645 5885 5905 5925 5945
vtxtable band 4 FATSHARK F FACTORY 5740 5760 5780 5800 5820 5840 5860 5880
vtxtable band 5 RACEBAND R FACTORY 5658 5695 5732 5769 5806 5843 5880 5917
vtxtable powerlevels 4
vtxtable powervalues 0 1 2 3
vtxtable powerlabels 25 100 200 300

# master
set dyn_notch_width_percent = 0
set dyn_notch_q = 250
set acc_calibration = -21,97,-528,1
set mag_hardware = NONE
set baro_hardware = NONE
set min_check = 1020
set max_check = 1980
set rssi_channel = 16
set dshot_bidir = ON
set motor_poles = 12
set ibata_scale = 1199
set beeper_dshot_beacon_tone = 2
set small_angle = 180
set osd_warn_rssi = ON
set osd_rssi_alarm = 70
set osd_rssi_pos = 14384
set osd_tim_2_pos = 14840
set osd_current_pos = 14336
set osd_mah_drawn_pos = 14797
set osd_craft_name_pos = 14346
set osd_warnings_pos = 14441
set osd_avg_cell_voltage_pos = 14378
set osd_flip_arrow_pos = 14570
set osd_stat_rtc_date_time = ON
set osd_stat_max_spd = OFF
set osd_stat_endbatt = ON
set osd_stat_bbox = OFF
set osd_stat_bb_no = OFF
set vcd_video_system = PAL
set name = QRC T79 Cine

profile 0

profile 1

profile 2

# restore original profile selection
profile 0

rateprofile 0

# rateprofile 0
set roll_srate = 50
set pitch_srate = 50
set yaw_srate = 50

rateprofile 1

rateprofile 2

rateprofile 3

rateprofile 4

rateprofile 5

# restore original rateprofile selection
rateprofile 0

# save configuration
save
#