# version
# Betaflight / STM32F411 (S411) 4.2.2 Aug 16 2020 / 01:47:01 (e833ac612) MSP API: 1.43
# config: manufacturer_id: MTKS, board_name: MATEKF411, version: be0c9205, date: 2020-01-15T19:44:32Z

# start the command batch
batch start

# reset configuration to default settings
defaults nosave

board_name MATEKF411
manufacturer_id MTKS
mcu_id 005d00563439510637393937
signature 

# name: FUS-RC

# map
map TAER1234

# serial
serial 0 8192 115200 57600 0 115200
serial 1 64 115200 57600 0 115200

# led
led 0 7,8::CB:6

# aux
aux 0 0 2 1950 2100 0 0
aux 1 0 0 1950 2075 0 0
aux 2 13 0 1425 1575 0 0
aux 3 35 0 1925 2100 0 0

# vtxtable
vtxtable bands 6
vtxtable channels 8
vtxtable band 1 BOSCAM_A A CUSTOM  5865 5845 5825 5805 5785 5765 5745 5725
vtxtable band 2 BOSCAM_B B CUSTOM  5733 5752 5771 5790 5809 5828 5847 5866
vtxtable band 3 BOSCAM_E E CUSTOM  5705 5685 5665    0 5885 5905    0    0
vtxtable band 4 FATSHARK F CUSTOM  5740 5760 5780 5800 5820 5840 5860 5880
vtxtable band 5 RACEBAND R CUSTOM  5658 5695 5732 5769 5806 5843 5880 5917
vtxtable band 6 IMD6     I CUSTOM  5732 5765 5828 5840 5866 5740    0    0
vtxtable powerlevels 3
vtxtable powervalues 0 1 2
vtxtable powerlabels 25 100 200

# master
set dyn_notch_width_percent = 0
set dyn_notch_q = 250
set acc_calibration = -156,49,-860,1
set rssi_channel = 16
set dshot_idle_value = 350
set dshot_bidir = ON
set motor_poles = 12
set vbat_min_cell_voltage = 320
set vbat_warning_cell_voltage = 340
set ibata_scale = 90
set small_angle = 180
set osd_rssi_alarm = 60
set osd_vbat_pos = 449
set osd_rssi_pos = 2105
set osd_tim_1_pos = 470
set osd_tim_2_pos = 2550
set osd_flymode_pos = 33
set osd_current_pos = 2530
set osd_mah_drawn_pos = 2540
set osd_craft_name_pos = 2060
set osd_avg_cell_voltage_pos = 2476
set vtx_band = 4
set vtx_channel = 5
set vtx_power = 1
set vtx_freq = 5820
set vcd_video_system = PAL
set gyro_1_align_yaw = 1800
set name = FUS-RC

profile 0

profile 1

profile 2

# restore original profile selection
profile 0

rateprofile 0

rateprofile 1

rateprofile 2

rateprofile 3

rateprofile 4

rateprofile 5

# restore original rateprofile selection
rateprofile 0

# save configuration
save