QUADIFYRC.COM
  • RC Cars
  • Car of the Month
  • Quad Reviews
  • COUPONS AND DISCOUNTS
  • About & Contact

Long Range Quads

lONG rANGE bUILD - gps, tbs cROSSFIRE AND bETAFLIGHT SETUP

29/1/2019

3 Comments

 
Introduction
​So now that that physical build is complete (minus the GPS) It's time to start setting everything up. I'll focus only on the elements unique to long range build beacuse I'll assume that anyone building a long range build is capable of setting up betaflight and BL Heli to their liking for basic quadcopter flight.
Crossfire and the X-lite
TBS Crossfire is new to me and was more of a learning curve than I was expecting having started with Flysky then moving to FRSKY a little over a year ago. My current transmitter is the TaranisX-Lite which I've reviewed here. In order to run crossfire on this I needed to purchase and adaptor that allowed the module to physically fit on the back of the x-lite and interfact electronically. This was easier than expected using a JR port adapter which I reviewed and streamlined in this blog. 
Picture
Picture
Picture
Easy to connect crossfire to the x-lite with this adapter. Check out my review here
Crossfire firmware update
Once connected, I set up a new model that disable the internal antenna (i.e. FRSKY protocol) and enable the crossfire module in the external module. Before anything else I used the TBS agent to update the crossfire micro transmitter module to the very latest firmware which allows it to run up to 250mW of power. This is a very worthy upgrade given this was only just bumped up from 50mW. TBS agent can be found here and is very easy to use:


http://www.team-blacksheep.com/corepro/agent
Picture
Crossfire transmitter and receiver setup
Once updated, power on your module and bind to you receiver (crossfire nano receiver for me). To do this follow the instructions below:

https://www.team-blacksheep.com/tbs-crossfire-micro-tx-quickstart.pdf

Once bound, your crossfire transmitter will update you receiver to the latest software automatically using the telemetry function. Very nice and a much better option that flashing physically like with frsky receivers!
By now you should be able to set the ideal settings using the crossfire lua script. Basic settings are: Use 868MHz if in Europe, 915MHz everywhere else; CRSF TX on output 1, CRSF RX on output 2. Your preference on maximum output power and whether dynamic power is on but I chose a fixed power of 100mW for stable and consistent link
Crossfire Betaflight Setup
Setup of in betaflight is simple - toggle serial RX on for the UART you wired the RX and TX wires into and then choose CRSF protocol as the serial based receiver type. Make sure you turn telemetry on as all crossfire receivers and transmitters support this function.
Crossfire antenna mounting
In terms of mounting your antenna the easiest option is the mount along the underside of an arm such that the elements on you immortal T antenna run perpindicular to the arm, parallel with the prop line. I chose my location as much for aesthetics as anything else.
Picture
Picture
I'm quite happy that this location keeps the antenna away from harm but does a reasonable job of keeping the active elements away from the frame - good enough for what I'm after.
GPS connection and mouning
Luckily for me GPS setup was mostly a simply excercise I chose the Betian BN-180 GPS unit which is cheap and runs the popular GLONASS protocol. Connect the RX and TX ports on the GPS to the TX and RX ports respectively of a spare UART (of which the Omnibus V6 has 5!) and then ground and 5v power from your FC. Mount the GPS 'upside down' so that the ceramic encase antenna is facing upwards towards GPS satelites in Earth orbit. MAKE SURE THE ANTENNA IS COMPLETELY IN THE OPEN. This was my biggest mistake on this build. I found a spot on top of the quad between the aluminium cage sides where there was good visibility from above but didn't realise the sides of the GPS antenna also need to be exposed. As soon as I figured this out I started getting satellite lock. It's now on an uglier but altogether more functional spot on the rear left arm. Of course it's easy writing about this now but being my first install it took me a good fewhours of troubleshooting! Other clever locations I've seen is the top of a go-pro mount or on top of a battery strap if a top-mount battery is used.
Picture
Picture
Top of the arm is a good location regardless of whether battery is top or bottom mount
GPS Betaflight setup
Setup on betaflight 3.5.3 (and later) was a dream - and I'll assume that you are using and F4 or greater processor in your flight controller because betaflight no longer has GPS support for F3 and older processors. Moving on, here are the step to set up GPS in betaflight:
  1. In the betaflight ports tab under the column heading 'sensor input' choose GPS from the dropdown box in the UART you wire the GPS to.
  2. In the configuration tab turn on the toggle switch for GPS, choose 'UBLOX' protocol and leave the rest as is.
  3. Now you will find a new GPS tab in betaflight where if you wait long enough and are not too far from outdoors, you see connections to GPS satellites within about 2 minutes. Once you have enough satellites to get a fully triangulated 3d lock it'll show your location on a map
GPS OSD options
With GPS now set up, you'll probably want to enable the features in betaflight OSD. personally I've used:
  • GPS Coordinates latitude and longitude. This means my DVR will show the last known location of the quad if it goes down
  • Home direction. Really useful for long range if you become disoriented. It's a small arrow that point bac to the location that your quad was armed - i.e. where you took off.
  • Speed. Just because it's awesome! And it's good for comparing to current draw to figure out the most efficient cruising speed for your quad.
  • Distance from home - Tells you how far you are out from where your quad was armed.
One thing to bear in mind is that with GPS enabled you now have a new flag for arming - GPS 3d lock. This means your quad CANNOT ARM without GPS lock. This can take up to about 1 minute from a cold start or less than 10-20 seconds if it was on recently. This is key for setting launch location for flight and cannot be bypassed. Easiest trick is the just change you powerup order so that your quad goes on first.
Given the extra data that is provided by GPS I'm tempted to pick up some more units for all my 5" and larger quads.
GPS rescue mode
One of the latest and greatest features of betaflight 3.5and up is GPS rescue mode where the quad will climb to a set altitude, yaw towards the home locations and then fly at a set angle towards home when you are more than 100m out. This is a great panic function if you are a long way out and suddenly loose video or something. Note, it won't get you home by itself but it will automatically get you back to a closey location where you may be able to recover video feed and then take back manual control. I'd recommend the official betaflight guide to GPS recue here to set this up.
Conclusion
Unfortunately this is probably the most boring but conversely hopefully the most useful section of my long range build series because I know it was certainly the most time consuming for me because I learnt as I went. Hopefully what this does mean though it that I've shared as I've learnt meaning it should be able to help someone in the same position as me. Obviously with the machine now set up I've been flying this big quad with a screen full of OSD and it's quite a unique experience - I've had up to 8 minutes flight on a 6s 1000mah battery. I've only been about 600m out so far but I plan to push it as time and space allows. Once I've pushed out further I plan to wrap up my build series with a reiview covering the performance of the quad and my findings.
If you found this article useful or helpful please feel free to like or share using the Facebook buttons below.
Picture
Picture
3 Comments

    Archives

    January 2019
    December 2018

    Categories

    All
    7 Inch
    Airbot
    Amain Hobbies
    Brother Hobby
    Clearview
    Crossfire
    Diatone
    Gemfan
    GPS
    HGLRC
    Iftron
    Parts List
    Rescue Mode
    Setup
    TBS
    VAS

    RSS Feed

Thanks for visiting QuadifyRC.com Follow us on facebook below to get all the latest updates
  • RC Cars
  • Car of the Month
  • Quad Reviews
  • COUPONS AND DISCOUNTS
  • About & Contact